Cintas Safety Certification for Maintenance Partners Practice Test

These questions are part of the practice quiz. Start practicing

• When must contractors view the safety video?
• When is the live-dead-live process used in LOTO procedures?
• What should be ensured about emergency lights in a fire inspection?
• Which of the following elements is NOT included in a Job Safety Analysis?
• How are the energy sources isolated during a lockout/tagout procedure?
• Which of the following liquids should be stored in a flammable liquid storage cabinet?
• What does the "Look, Listen, Feel" process pertain to?
• Why do we install guards around chemical pumps?
• What hazard is associated with flexible cords in excess of 50V being attached with plastic rigid ties to metal structures?
• What safety document is necessary if trenching is involved in the project?
• What is the maximum temperature that a load of Non-Mat bulk should be at after being unloaded?
• Why are missing knockouts on electrical panels and junction boxes not allowed?
• What is the significance of personal locks in a Group LOTO?
• Which characteristic makes a confined space a permit required confined space (PRCS)?
• What is a universal precaution when handling blood?
• What is the proper position for the dryer sprinkler water supply valve?
• What is the safety vision of Cintas?
• Why do new partners need to perform Annual Periodic Inspections (API)?
• What category of LOTO identifies all energy sources for equipment isolation?
• Why must only certain pipes and steam traps be guarded, specifically those within 7 feet of a walking surface?
• Why can't propane tanks for BBQ grills be stored on their side?
• What training must a Hot Work Fire Watch have?
• What must be done to rotating shafts, regardless of their protrusion?
• Where are GFCI outlets required to be installed?
• When are shift change locks required, and what is their purpose?
• Which factor does NOT affect mechanical action in a washer?
• What potential actions might be taken against someone who bypasses safety devices?
• What is required if the project involves working in confined spaces?
• At what decibel level is corrective action required for noise exposure?
• How often should welding hoses or cables be checked for damage?
• What is one reason to review LOTO procedures before performing maintenance on equipment?
• Why is it important for the live electrical permit to be approved?
• What system must an authorized partner follow to enter the wash alley?
• During LOTO procedures, what is the purpose of identifying disconnects and labels?
• Which method is used to determine the root cause of an incident?
• Why is partner involvement critical in the Safety Improvement Committee?
• What is the minimum width required for an egress?
• What document must contractors submit before performing work at a location?
• How often should sprinklers be visually inspected?
• What should you look for during a visual inspection of a plant sprinkler system?
• If the job involves welding on stainless steel, what must be done?
• How often is the Wash Alley "rules" permit reviewed?
• What does LOTO stand for in safety procedures?
• Which of the following is NOT a critical item related to water that must be checked on a washer?
• What must contractors acknowledge before being allowed in the wash alley?
• What is the primary purpose of Group LOTO?
• Who uses the Maintenance Access Gate Key Log at WASS facilities?
• How often must Annual Periodic Inspections (API) be performed?
• What procedure must outside contractors follow to access the roof?
• What is the reason for requiring proper strain relief for pendant cords?
• What are the primary risks associated with confined spaces?
• What is the maximum gap allowed in guarding fans to prevent accidental contact?
• Which type of work is NOT typically covered under the contractor safety program?
• Why is it crucial to conduct monthly ladder inspections?
• What is the main goal of the near-miss program?
• Which of the following tasks requires the use of a personal fall protection system?
• What type of storage container is approved for storing fuel?
• What tools are essential for performing wall penetration tasks?
• What is one of the hazards associated with drywall penetration?
• What could be a consequence of not using proper GFCI outlets near water sources?
• What are some hazards present when working in a manual wash alley?
• Who is allowed to weld on stainless steel at Cintas?
• Why should plant sprinkler main control valves be chained open?
• What must Contractors receive prior to entering the Wash Alley for the first time?
• How often are fire drills and severe weather drills conducted?
• Which of the following is not a maintenance-related item contributing to dryer fires?
• At what temperature should pipes and steam traps be guarded?
• Why is the LOTO equipment inventory necessary?
• How often are pony washer and dryer interlocks checked?
• When should LOTO procedures be followed?
• What is typically discussed during the pre-job briefing?
• What could happen if one of the components of the wash pie is inadequate?
• What is the recommended trip current for a GFCI?
• What should you check before restoring service to a piece of equipment?
• Which program must be reviewed by corporate safety for scaffolding work?
• What must Cintas location management complete before a bulk chemical delivery?
• Which program must be submitted if the scope of work involves Lockout/Tagout (LOTO)?
• What is a potential outcome of leaving chemical spills uncleaned?
• How many spare compressed tanks (oxygen/acetylene) can be stored at a location?
• What is the purpose of the Issuance of Replacement Safety Devices Log?
• What is necessary to confirm the equipment is in a safe state before starting it again?
• What document should you use to record sprinkler inspections?
• What should each partner or contractor do when involved in Group LOTO?
• What is the reason for inspecting voltage-rated gloves prior to each use?
• What type of clothing is part of the personal protective equipment for electrical safety?
• Which factor is critical for the safety observation process?
• Which item is shared among the electrical safety program tools?
• What is the definition of egress in a workplace?
• Why are extension cords not permitted for permanent use?
• Why are safety checks important to perform on the shuttle and pony washer/dryer interlocks?
• What is the first step in the lockout/tagout procedure?
• What type of training is required for maintenance partners working in the wash alley?
• What communication method must maintenance partners use when working in the wash alley?
• What type of permit is commonly required for routine work?
• What must contractors provide if equipment is used in a live environment?
• In which scenario is a non-routine work permit typically required?
• What element must be checked on a fire extinguisher during inspections?
• What should contractors do if they encounter lead paint or asbestos?
• What is a key consequence of improper handling of welding materials during a fire incident?
• What risk is associated with improperly labeled drum wands?
• Which of the following is NOT a confined space at your facility?
• What must be done if a contractor has to perform work in pits?
• What must maintenance partners do before performing extended work in the wash alley?
• What should happen to cigarettes at closing time?
• What are the three elements of a Confined Space?
• What does PRCS stand for in the context of LOTO procedures?
• What can you determine by observing a load through a washer's glass door?
• What must contractors do upon arriving at the work location?
• What is a Task Based JSA?
• What is the purpose of having a chemical inventory and approval process?
• Why is an 18-inch clearance required for a fire sprinkler head?
• When using an extension ladder, what situation requires fall protection?
• What should be done if welding is required on a dryer drum?
• What type of PPE is recommended when responding to an incident involving blood?
• How often should the dryer fire suppression system be inspected and tested?
• Why is maintenance involvement crucial in ergonomics?
• What is a requirement for a guard rail on a mezzanine?
• What must be done to a piece of equipment when it is placed out of service?
• Why should the sprinkler flow alarm be tested?
• What safety requirement involves completing a daily observation during the project?
• What is the primary purpose of a Job Safety Analysis (JSA)?
• How often are automated shuttle safety devices checked?
• What should be checked for coolness with a Fluke meter at closing time?
• What is stored in a locked cabinet at WASS facilities?
• How often must plumbed eyewash stations be inspected?
• What items are included in a fire inspection form?
• What must be present at eyewash stations to ensure their functionality?
• What is an important factor when inspecting hand and power tools?
• What is required for Cintas partners to access the roof?
• What is the primary reason for labeling valves and disconnects?
• How should soiled ink/furniture towels be stored?
• Why must compressed gas cylinders be stored upright?
• What is the first step in the live-dead-live process?
• Which of the following is NOT one of the five components of the laundering process wash pie?
• What information is included on an arc flash label?
• How often must ladders be inspected according to the ladder inspection program?
• How frequently should safety observations be conducted for new hires within the first month?
• Where should propane tanks be stored?
• For work at heights, what must be submitted prior to job commencement?
• Who are the authorized PIT users at Cintas locations?
• What is the first step when incorporating new equipment into the LOTO program?
• What is one of the key components of E-stop checks?
• What types of items should never be placed in a flammable liquid storage cabinet?
• Why must the area around a fire extinguisher remain clear?
• What is a key component of heat stress prevention?
• Why is secondary containment required for containers in use?
• During a power outage, who should monitor the wash alley to prevent fires?
• Can acetylene and oxygen be stored together when not in use?
• Why do we use labels on switches, breakers, and electrical disconnects?
• Why must all chemical containers be labeled with a GHS label?
• When is it not permitted to stand in a red zone?
• How should maintenance partners respond to the issues raised in the Safety Improvement Committee meetings?
• What is the maximum time-weighted average allowed for noise exposure in the workplace?
• What does BBP stand for and how can it enter the body?
• Are plastic fuel containers allowed at Cintas?
• What precautions should be taken when responding to incidents involving human blood?
• What is a critical inspection component for documenting the dryer fire suppression system tests?
• What can be a consequence of intentionally removing safety devices or guards?
• What precaution should be taken when welding stainless steel?
• What is the purpose of a live electrical permit?
• What is a significant hazard when performing hot work in a confined space?
• What is a key reason for having a Safety Improvement Committee?
• What should you NOT do if a dryer fire occurs?
• Why is it important to take a temperature reading for Non-Mat bulk products?
• Why is it crucial to have a monitor when performing work on the roof?
• Do contractors need to follow lockout/tagout (LOTO) procedures, and why is this necessary?
• Where are red zones located in the wash alley?
• What should you do if a load comes out of the dryer with a temperature exceeding the limit?
• What type of permit is needed for overhead work that doesn't have Cintas monitoring?
• How can you ensure the sprinkler water supply valve remains in the right position?
• What is the purpose of storing soiled towels in a closed drum?
• Why is a fire extinguisher needed on welding or torch carts?
• What should you do if a fire extinguisher is blocked?
• What must self-contained eyewash stations have to meet inspection requirements?
• What is the primary purpose of installing guards or shatter shields for fluorescent bulbs?
• What documentation is required for a Confined Space Entry Program?
• What is one critical reason for keeping electrical panels and disconnects free of obstructions?
• How frequently should personal fall protection equipment be inspected by partners?
• What is the purpose of the roof access permit process for Cintas partners?
• What should you do regarding dryer doors while the power is out and smoke is observed?
• What is the primary purpose of a safety observation program (CSOP)?
• How often should the dryer sprinkler system be tested?
• How often must the emergency stops (E-Stops) on equipment be checked?
• What is the purpose of a documented checklist for ladder inspections?
• What hazard does accumulated lint pose if not appropriately managed?
• What is the purpose of a closing time report?